How to Install a Ghost Immobiliser
A ghost immobiliser guards your vehicle from key cloning or hacking. It works by stopping the engine from starting until a PIN code has been entered. It can be as long as 20 characters.
It is undetectable by thieves and they are unlikely to expect this extra layer of security. Some systems have an app which allows the owner to disarm their immobiliser in the event of forgetting their PIN code or to utilize the service/valet mode.
Connecting the vehicle's CAN Bus
The Ghost 2 Immobiliser is an advanced security system that is able to be integrated into your vehicle's ECU offering a secure security line against thieves. It is highly efficient and user-friendly. This makes it an excellent addition to your vehicle's security arsenal. However, just like any other anti-theft device, it is not impervious to failure and requires regular maintenance to ensure its operation. This guide will help you get the most of your Ghost 2 immobiliser.
CAN (Controller Area Network) is a robust serial network that lets microcontrollers communicate with one another in short distances, without the necessity of a central control unit. It is designed to multiplex electrical wiring in vehicles, thereby saving on copper. It offers many advantages including the low cost and ease of use.
The CAN protocol is used in most modern automobiles to connect with the engine management system, transmission controller, steering control module, air conditioning controls, and more. It also transmits sensor data, such as speed sensors and inputs, to control various features of the vehicle. The CAN bus is able to monitor the health of these different components. It can prevent the vehicle from starting if it's in an unsafe condition.
Although the CAN bus can be used for a variety of purposes, it's crucial to understand how it works and how it's secured. The CAN bus is a great way to enhance the features of your vehicle, but it's vital to protect it from threats such as hackers and other. Installing a firewall and monitoring your CAN bus with software is the best method to accomplish this.
Ghost2's secluded control unit is concealed inside the car's wiring harness or dashboard, which eliminates the possibility of a thief physically altering it. It's also impossible to reset the PIN or emergency code without access to the vehicle.
If you have to hand over your vehicle to a valet parking service, maintenance, or any other reason, you can use the Transport Mode. This feature disables the Ghost immobiliser's ignition and keyfob functions, and will only be activated when the car reaches 31 mph for 15 minutes.
How to create a PIN code
The Ghost immobiliser shields your vehicle from thieves. The cutting-edge technology uses an PIN code to shut down the engine and block it from starting if you do not have the correct code or an authorized fob or mobile device. The system's subtle design makes it unnoticeable, and provides unparalleled protection against theft. The system is TASSA-certified and can save you significant amounts on your car insurance.
During the installation when you install the Ghost system goes into a learning mode to record the sequence of buttons pressed to create your unique pin code. Once the pin code has been created, the installer will then guide you through the steps to activate the system. Once activated, the Ghost system disables your vehicle's starting motor unless you enter a valid PIN or switch the vehicle to transport mode. This makes it difficult for thieves or cloners who want to hack or clone your vehicle's starter system.
It's easy to set up it is easy to install a Ghost immobiliser, but you must follow the specific instructions provided in the user guide to ensure the proper operation. Hand tools and multimeters can be used to verify electrical values. Insulation tape and heat shrink tubing may shield the wire from damage, while cable tie is essential to keep everything tidy and secure. Be certain to test the system regularly to identify any potential issues and mistakes.
It is important to check the system one final time prior to turning on the ignition. The Ghost immobiliser will re-arm itself after 3 to 30 seconds, based on the vehicle's model. The system also comes with a Service/Valet mode that allows you to temporarily disable the system to service or valet parking.
The immobiliser can be hidden beneath the dashboard or the steering wheel. It is recommended to use a small bit of paint or duct tape to mark the CAN H and CAN L wires to ensure that you easily find the wires during testing. The CAN H and the L wires must also be connected to an electrical source that delivers continuous 12V. It is crucial to verify the connections again after testing as incorrect identification of these wires could cause system malfunction.
Activating the system
A ghost immobiliser stops your vehicle from starting unless you press a set of buttons inside the car typically the steering wheel, door panel, or central console. The sequence can be changed by the user if needed. Once the system is activated it cannot be deactivated by thieves which makes it a great option for anyone looking to secure their vehicle from theft.
The device is not designed to be able to be detected by modern diagnostic and code-grabbing techniques. It also doesn't broadcast radio signals which makes it difficult for thieves to find the device.
If the device is located, it will stop the engine from running. It will also sound an alarm to scare the burglar away. The device can be used to monitor the location of a car which can aid in the search for the vehicle if it is taken.
Contact Car Specalist Customs for a estimate or to discuss your options if you're interested in an immobiliser that is ghost-like. We are fully trained to install a ghost immobiliser for your vehicle and will ensure it is hidden in a remote area. We can also install other security measures, including the kill switch and wheel lock to protect your vehicle from theft.
Disarming the system
If you have a Ghost immobiliser that is fitted to your vehicle, it's essential to know how you can disable it. It can be used in the event that you lose your keys or your car battery dies. The system uses an individual PIN code that only you know, so the immobiliser won't start your vehicle without entering this code. Pressing a combination buttons on the steering wheel or on the dashboard is the most efficient method of entering your code. This is much easier than using a key fob. It also keeps others from copying the remote.
Ghost2 isn't intrusive unlike other immobilisers from the aftermarket that require cutting wires for installation. It also works with the CAN bus system of your vehicle to function. Its most prominent characteristic is that it disables the engine without affecting functions of the vehicle. This makes it very difficult for thieves to use signal boosters or to clone keys for cars. autowatch ghost 2 immobiliser G28 Car Keys does not emit radio frequency, so thieves won't be able to detect it.
The Ghost system comes with a Transport Mode that allows you to temporarily disable security for situations such as transportation or service. This feature is ideal for when you're loaning your vehicle to someone else without sharing your PIN code, or if your vehicle requires to be protected when you drive it. Press the service button five times over 2 seconds to activate Transport Mode. The Ghost system will confirm activation using five indication signals.
Save the emergency code in your vehicle in a secure place. If you ever get locked out of your car you can contact the company or technician who installed the system and they will give you the code. If they are not able to contact you then you can try to contact an authorized dealer however this will require verification procedures and could incur additional charges.
This system is not just practical, but it can also protect your vehicle from theft, and also reduce the cost of insurance. Many insurance companies offer reduced costs or financial incentives for those who install this anti-theft system.